mersenneforum.org  

Go Back   mersenneforum.org > New To GIMPS? Start Here! > Information & Answers

Reply
 
Thread Tools
Old 2018-02-27, 18:58   #1
artesina
 
Feb 2018

5 Posts
Default Problem with prime 95 in worker #8

i have a problem with owrker 8
[Feb 27 19:03] Worker starting
[Feb 27 19:03] Beginning a continuous self-test on your computer.
[Feb 27 19:03] Please read stress.txt. Choose Test/Stop to end this test.
[Feb 27 19:03] Test 1, 1800000 Lucas-Lehmer iterations of M250519 using FMA3 FFT length 12K, Pass1=256, Pass2=48, clm=1.
[Feb 27 19:05] Test 2, 1800000 Lucas-Lehmer iterations of M245759 using FMA3 FFT length 12K, Pass1=256, Pass2=48, clm=1.
[Feb 27 19:06] Test 3, 1800000 Lucas-Lehmer iterations of M245281 using FMA3 FFT length 12K, Pass1=256, Pass2=48, clm=1.
[Feb 27 19:08] Test 4, 1800000 Lucas-Lehmer iterations of M243713 using FMA3 FFT length 12K, Pass1=256, Pass2=48, clm=1.
[Feb 27 19:09] Self-test 12K passed!
[Feb 27 19:09] Test 1, 3200000 Lucas-Lehmer iterations of M172031 using FMA3 FFT length 8K, Pass1=128, Pass2=64, clm=2.
[Feb 27 19:11] Test 2, 3200000 Lucas-Lehmer iterations of M163839 using FMA3 FFT length 8K, Pass1=128, Pass2=64, clm=2.
[Feb 27 19:13] Test 3, 3200000 Lucas-Lehmer iterations of M159745 using FMA3 FFT length 8K, Pass1=128, Pass2=64, clm=2.
[Feb 27 19:15] Self-test 8K passed!
[Feb 27 19:15] Test 1, 1400000 Lucas-Lehmer iterations of M315393 using FMA3 FFT length 15K, Pass1=320, Pass2=48, clm=2.
[Feb 27 19:16] Test 2, 1400000 Lucas-Lehmer iterations of M311295 using FMA3 FFT length 15K, Pass1=320, Pass2=48, clm=2.
[Feb 27 19:17] FATAL ERROR: Rounding was 0.5, expected less than 0.4
[Feb 27 19:17] Hardware failure detected, consult stress.txt file.
[Feb 27 19:17] Torture Test completed 8 tests in 13 minutes - 1 errors, 0 warnings.
[Feb 27 19:17] Worker stopped.
you know what is my problem?
I run the test because after a game into "assetto corsa" after one or two hours windows give an error, so some friends sudgest this test runned with the max hoit temperature (no ram test)
the temperatures was max 69 degrees
you can help me?
I'm a beginner and i don't know what I cvan do now (I can't see the txt file where is it?)
thx in advance and sorry for my poor english
artesina is offline   Reply With Quote
Old 2018-02-27, 20:02   #2
VBCurtis
 
VBCurtis's Avatar
 
"Curtis"
Feb 2005
Riverside, CA

2·2,239 Posts
Default

1. Reduce your overclock.
2. Clean your system of dust.
3. If one core is much hotter than the others, your CPU heatsink may not be installed well.
VBCurtis is online now   Reply With Quote
Old 2018-02-27, 20:02   #3
artesina
 
Feb 2018

1012 Posts
Default

NOW Similar error in worker #7


[Feb 27 20:26] Worker starting
[Feb 27 20:26] Beginning a continuous self-test on your computer.
[Feb 27 20:26] Please read stress.txt. Choose Test/Stop to end this test.
[Feb 27 20:26] Test 1, 1800000 Lucas-Lehmer iterations of M250519 using FMA3 FFT length 12K, Pass1=256, Pass2=48, clm=1.
[Feb 27 20:28] Test 2, 1800000 Lucas-Lehmer iterations of M245759 using FMA3 FFT length 12K, Pass1=256, Pass2=48, clm=1.
[Feb 27 20:29] Test 3, 1800000 Lucas-Lehmer iterations of M245281 using FMA3 FFT length 12K, Pass1=256, Pass2=48, clm=1.
[Feb 27 20:31] Test 4, 1800000 Lucas-Lehmer iterations of M243713 using FMA3 FFT length 12K, Pass1=256, Pass2=48, clm=1.
[Feb 27 20:32] Self-test 12K passed!
[Feb 27 20:32] Test 1, 3200000 Lucas-Lehmer iterations of M172031 using FMA3 FFT length 8K, Pass1=128, Pass2=64, clm=2.
[Feb 27 20:34] Test 2, 3200000 Lucas-Lehmer iterations of M163839 using FMA3 FFT length 8K, Pass1=128, Pass2=64, clm=2.
[Feb 27 20:36] Test 3, 3200000 Lucas-Lehmer iterations of M159745 using FMA3 FFT length 8K, Pass1=128, Pass2=64, clm=2.
[Feb 27 20:38] Self-test 8K passed!
[Feb 27 20:38] Test 1, 1400000 Lucas-Lehmer iterations of M315393 using FMA3 FFT length 15K, Pass1=320, Pass2=48, clm=2.
[Feb 27 20:40] Test 2, 1400000 Lucas-Lehmer iterations of M311295 using FMA3 FFT length 15K, Pass1=320, Pass2=48, clm=2.
[Feb 27 20:41] Test 3, 1400000 Lucas-Lehmer iterations of M308295 using FMA3 FFT length 15K, Pass1=320, Pass2=48, clm=2.
[Feb 27 20:43] Test 4, 1400000 Lucas-Lehmer iterations of M307201 using FMA3 FFT length 15K, Pass1=320, Pass2=48, clm=2.
[Feb 27 20:44] Self-test 15K passed!
[Feb 27 20:44] Test 1, 2200000 Lucas-Lehmer iterations of M212991 using FMA3 FFT length 10K, Pass1=128, Pass2=80, clm=2.
[Feb 27 20:45] FATAL ERROR: Rounding was 0.5, expected less than 0.4
[Feb 27 20:45] Hardware failure detected, consult stress.txt file.
[Feb 27 20:45] Torture Test completed 11 tests in 18 minutes - 1 errors, 0 warnings.
[Feb 27 20:45] Worker stopped.
artesina is offline   Reply With Quote
Old 2018-02-27, 20:11   #4
artesina
 
Feb 2018

1012 Posts
Default

Quote:
Originally Posted by VBCurtis View Post
1. Reduce your overclock.
2. Clean your system of dust.
3. If one core is much hotter than the others, your CPU heatsink may not be installed well.
the thest is the torture test without ram test , only cpu for hot temperature test
the pc is new with z270m motherboard
no ovreclock
two slot of ram
the core temp prog. said:
62 to 68 degrees max difference
the core tem was a good method for see temp?
What you sudgest now?
I buy from a online store and now I don't known what I can do :(
the pc it is a mid case with gygabyte aours gtx 1080ti and and i7 7700k 4200
g skill ram c14 or c15 I don't remeber.
only few months

Last fiddled with by artesina on 2018-02-27 at 20:18
artesina is offline   Reply With Quote
Old 2018-02-27, 20:29   #5
artesina
 
Feb 2018

516 Posts
Default

the medium tst with some ram test is workers 7
[Feb 27 21:13] Worker starting
[Feb 27 21:13] Beginning a continuous self-test on your computer.
[Feb 27 21:13] Please read stress.txt. Choose Test/Stop to end this test.
[Feb 27 21:13] Test 1, 36000 Lucas-Lehmer iterations of M7998783 using FMA3 FFT length 400K, Pass1=320, Pass2=1280, clm=4.
[Feb 27 21:16] Test 2, 36000 Lucas-Lehmer iterations of M7798785 using FMA3 FFT length 400K, Pass1=320, Pass2=1280, clm=4.
[Feb 27 21:19] Self-test 400K passed!
[Feb 27 21:19] Test 1, 140000 Lucas-Lehmer iterations of M2605473 using FMA3 FFT length 128K, Pass1=512, Pass2=256, clm=2.
[Feb 27 21:19] FATAL ERROR: Rounding was 9185070.543, expected less than 0.4
[Feb 27 21:19] Hardware failure detected, consult stress.txt file.
[Feb 27 21:19] Torture Test completed 2 tests in 5 minutes - 1 errors, 0 warnings.
[Feb 27 21:19] Worker stopped.
--------------------------------------------------------------
worker 8

[Feb 27 21:13] Worker starting
[Feb 27 21:13] Beginning a continuous self-test on your computer.
[Feb 27 21:13] Please read stress.txt. Choose Test/Stop to end this test.
[Feb 27 21:13] Test 1, 36000 Lucas-Lehmer iterations of M7998783 using FMA3 FFT length 400K, Pass1=320, Pass2=1280, clm=4.
[Feb 27 21:16] Test 2, 36000 Lucas-Lehmer iterations of M7798785 using FMA3 FFT length 400K, Pass1=320, Pass2=1280, clm=4.
[Feb 27 21:19] Self-test 400K passed!
[Feb 27 21:19] Test 1, 140000 Lucas-Lehmer iterations of M2605473 using FMA3 FFT length 128K, Pass1=512, Pass2=256, clm=2.
[Feb 27 21:20] Test 2, 140000 Lucas-Lehmer iterations of M2584313 using FMA3 FFT length 128K, Pass1=512, Pass2=256, clm=2.
[Feb 27 21:21] Test 3, 140000 Lucas-Lehmer iterations of M2573917 using FMA3 FFT length 128K, Pass1=512, Pass2=256, clm=2.
[Feb 27 21:22] Test 4, 140000 Lucas-Lehmer iterations of M2540831 using FMA3 FFT length 128K, Pass1=512, Pass2=256, clm=2.
[Feb 27 21:22] FATAL ERROR: Rounding was 0.5, expected less than 0.4
[Feb 27 21:22] Hardware failure detected, consult stress.txt file.
[Feb 27 21:22] Torture Test completed 5 tests in 8 minutes - 1 errors, 0 warnings.
[Feb 27 21:22] Worker stopped.
artesina is offline   Reply With Quote
Old 2018-02-27, 20:51   #6
artesina
 
Feb 2018

5 Posts
Default

AFTER TEST FAILURE THE CORE 3 ( WITH CORE TEMP) SHOW A BURDEN DOWN rduced at 1-3 % , OTHER CORES continuous to run at 100% BURDEN .
I SUPPOSE THE CORE tested DOESNT WORK AFTER THE erros previous attached. it is correct?
thx
artesina is offline   Reply With Quote
Reply

Thread Tools


Similar Threads
Thread Thread Starter Forum Replies Last Post
Prime 95 will not let me change cores per worker evanh Software 4 2017-12-22 22:25
Worker #5 and Worker#7 not running (Error ILLEGAL SUMOUT skrupian08 Information & Answers 9 2016-08-23 16:35
Cullen prime problem Citrix Prime Cullen Prime 22 2007-02-23 10:46
prime problem Agrajag Puzzles 20 2004-06-09 09:34
Problem running prime-net on debian (woody) dual processor thedagit Software 3 2002-10-19 05:57

All times are UTC. The time now is 00:30.

Fri Nov 27 00:30:39 UTC 2020 up 77 days, 21:41, 4 users, load averages: 1.31, 1.50, 1.49

Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2020, Jelsoft Enterprises Ltd.

This forum has received and complied with 0 (zero) government requests for information.

Permission is granted to copy, distribute and/or modify this document under the terms of the GNU Free Documentation License, Version 1.2 or any later version published by the Free Software Foundation.
A copy of the license is included in the FAQ.