20160407, 13:29  #1 
Apr 2016
1101_{2} Posts 
Resuming yafu job (ecm)
Is it possible to somehow configure yafu so hat it would be possible to resume yafu if yafu process is terminated?
I see in docfile.txt that some resumption is possible for seiving, but what about ECM? How complicated would be to implement yafu ECM strategy in script that uses gmpecm directly? 
20160407, 13:57  #2 
Basketry That Evening!
"Bunslow the Bold"
Jun 2011
40<A<43 89<O<88
7221_{10} Posts 
You can use the work option to tell Yafu a certain amount of ECM has already been done

20160407, 19:34  #3 
Apr 2016
D_{16} Posts 
Thanks for the hint!
For example, if I have this kind of output, what value should I pass to the work option? Code:
fac: setting target pretesting digits to 182.15 fac: t15: 1.07 fac: t20: 0.04 fac: estimated sum of completed work is t15.19 fac: work done at B1=11000: 0 curves, max work = 74 curves fac: 74 more curves at B1=11000 needed to get to t182.15 ecm: found prp16 factor = 6586291483612179 fac: setting target pretesting digits to 177.54 fac: t15: 1.73 fac: t20: 0.15 fac: estimated sum of completed work is t15.73 fac: work done at B1=11000: 8 curves, max work = 74 curves fac: 66 more curves at B1=11000 needed to get to t177.54 ecm: 72/72 curves on C577, B1=11K, B2=gmpecm default fac: setting target pretesting digits to 177.54 fac: t15: 7.73 fac: t20: 1.12 fac: t25: 0.05 fac: estimated sum of completed work is t20.26 fac: work done at B1=50000: 0 curves, max work = 214 curves fac: 214 more curves at B1=50000 needed to get to t177.54 ecm: 216/216 curves on C577, B1=50K, B2=gmpecm default, ETA: 4 sec pm1: starting B1 = 3750K, B2 = gmpecm default on C577 fac: setting target pretesting digits to 177.54 fac: t15: 38.59 fac: t20: 11.40 fac: t25: 1.06 fac: t30: 0.07 fac: estimated sum of completed work is t25.34 fac: work done at B1=250000: 0 curves, max work = 430 curves fac: 430 more curves at B1=250000 needed to get to t177.54 ecm: 432/432 curves on C577, B1=250K, B2=gmpecm default, ETA: 20 sec pm1: starting B1 = 15M, B2 = gmpecm default on C577 fac: setting target pretesting digits to 177.54 fac: t15: 124.99 fac: t20: 65.40 fac: t25: 9.70 fac: t30: 1.07 fac: t35: 0.09 fac: estimated sum of completed work is t30.46 fac: work done at B1=1000000: 0 curves, max work = 904 curves fac: 904 more curves at B1=1000000 needed to get to t177.54 ecm: 904/904 curves on C577, B1=1M, B2=gmpecm default, ETA: 1.4 min fac: setting target pretesting digits to 177.54 fac: t15: 426.32 fac: t20: 246.20 fac: t25: 54.90 fac: t30: 8.73 fac: t35: 1.09 fac: t40: 0.11 fac: estimated sum of completed work is t35.56 fac: work done at B1=3000000: 0 curves, max work = 2350 curves fac: 2350 more curves at B1=3000000 needed to get to t177.54 ecm: 424/2352 curves on C577, B1=3M, B2=gmpecm default, ETA: 14.67 hrs hrs 
20160407, 21:41  #4 
Basketry That Evening!
"Bunslow the Bold"
Jun 2011
40<A<43 89<O<88
7221_{10} Posts 
Code:
fac: estimated sum of completed work is t35.56 ... ecm: 424/2352 curves on C577, B1=3M, B2=gmpecm default, ETA: 14.67 hrs hrs 
20160613, 11:39  #5 
Apr 2016
13 Posts 
Nice, thank you!
I will parse the output from yafu to calculate the work done. In this progress line Code:
ecm: 424/2352 curves on C577, B1=3M, B2=gmpecm default, ETA: 14.67 hrs rs Code:
ecm: 424/2352 (to get from t25 to t30) curves on C577, B1=3M, B2=gmpecm default, ETA: 14.67 hrs rs 
Thread Tools  
Similar Threads  
Thread  Thread Starter  Forum  Replies  Last Post 
Running YAFU via Aliqueit doesn't find yafu.ini  EdH  YAFU  8  20180314 17:22 
Pausing/resuming a process automatically?  Xyzzy  Linux  6  20170622 19:58 
Resuming aliqueit  johnadam74  Aliquot Sequences  4  20160328 12:32 
Resuming after a hard drive crash  delta_t  Software  4  20030626 13:54 
Resuming work  rc  Software  9  20030208 15:08 